After years of lusting after this bike, I finally had my dream come true. Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Road King Classic Custom models. Always use the turn signals when you intend to change lanes or make a turn. One guy I met at the local bike shop said he has never even seen one at any of the local meetups, and he's gone to them for years. Fig 3 Figure 1 Figure 2 Figure 3 - 3 — 2. No more ruining your expensive paper shop manual with grease and dirt.Next
If there is still no spark, consult your Suzuki dealer for repairs. Inspect and main- tain the brake pads as recom- mended. If you do not have one, ask your Suzuki dealer to perform this adjustment. To close the fuel tank cap, push the cap down firmly with the key in the cap lock. I did find the service manual online in pdf format, but I'm looking for the owners manual. Note the position of the roll pin. Its easy to find the solution to virtually any query on this forum.
The brake light will be illuminated when the rear brake is operated. . Three spare fuses one 15A and two fuse blows in a short time, consult your 10A are provided inside the fuse box. Enjoy the bike and its rarity - people will wonder what the hell it is. Immobilizer system is designed to help pre- vent motorcycle theft by electronically dis- abling the engine starting system.
If you Select a range position according. Starting your journey with bikes from this one is like a recipe for madness. To remove the rear seat, pull the seat lock wire. When I found out it went into production, the first thing I did was get my endorsement. To adjust the throttle cable play: 1.Next
I'm planning to do most of the service myself so advice appreciated. Transfer body weight to the rear by sliding back on the hills improperly can cause loss seat. Therefore, your model may have different standard features than shown in this manual. If the engine refuses to start, perform the fol- lowing inspections to determine the cause. Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. Install stock solo seat mount bracket using two stock screws saved in Step 2. Welcome to the King Forum and to King ownership.Next
Never carry a helmet fastened to the hel- met holder. Suzuki dealer or a qualified mechanic immediately. To set the compression damping force adjuster to the standard position, turn the adjuster clockwise until it stops and then turn it counterclockwise 2 turns until the two. Fix the helmet securely atop the seat if you must carry it. There are also a total of 7 washers.
Front axle tightening torque: 100 N·m 10. Adjust the drive chain slack by turning the right and left chain adjuster bolts 3. Place an accessory service stand or an equivalent stand under the swingarm to help stabilize the rear end. Installation 1 Set the front fork to the front fork lower bracket temporarily by tightening the lower clamp bolts 1. Remove the head- light lower cover 2 by unhooking the 5.Next
If incorrect free play in this cable is suspected due to inconsistent cruise operation or because of inconsistent idle speed, the adjusters on the throttle cable from the hand grip must be backed all the way off to give as much free play as possible. As to why I have it as my first bike. Put the circle end of the prop stay onto the steering lock assembly. Disconnect the air cleaner sen- 17. Be careful not to allow stud plate to fall through the fender. Pull off the bulb from the socket. After installing seat, pull upward on front of seat to be sure it is in locked position.Next
There is an owners location map on the forum somewhere so you can find another local owner. The power is unbelievable and it's a great commuter as well. I'm tired of living a mundane life where I'm shackled by my primary vehicle, not wanting to go anywhere more than a 45 minute radius in fear of breaking down and being stranded, but I can't afford a new car. This is a great way to build up my credit so in the future I can do just that. Tightening torque Front fork lower clamp bolt b : 23 N·m 2. Collection of this residue is normal at all times.Next
To reinstall the seat, slide the seat hooks into the seat hook retainers and push down firmly until the seat snaps into locked posi- tion. After the engine cools, wrap a thick cloth around cap and carefully remove the cap by turning it a quarter turn to allow pressure to escape and then turn the cap all the way off. The running time counts from when the running time is reset. Use a brush to remove carbon deposits from spark. Be sure to keep oil and solvent away from children and pets.Next